A soft blue drying towel being laid over a freshly washed black car at EXD in Hyde Park.

EXD_ Care Guides · Wash and care

Bird droppings and tree sap: what to do in the first hour

Get droppings and sap off in the first hour, in the shade, without rubbing. Soften droppings with a quick detailer or a warm wet microfibre, then lift them in one direction. Sap needs a dedicated tar and sap remover made for car paint. Repeat rather than press, then rinse and check the spot in good light.

Avi Nair, EXD · About 4 minutes · Published 26 June 2026

Every October someone parks under a jacaranda in Parkhurst and learns two things. The flowers are lovely. The birds in the tree are not.

A dropping on paint is a small problem that turns into a bigger one with heat and time. Deal with it today and it's usually gone without a trace. Leave it for the weekend wash and it may leave a dull outline in the clear coat.

The first hour is what matters. After that, you're buying time.

Why droppings etch

You'll often read that droppings etch because they're acidic. The research is more interesting. A study on automotive clear coat measured real droppings at close to neutral and found the damage comes mostly from digestive enzymes breaking down the clear coat, and that heat and UV make it worse. Damage rose with temperature up to 60°C. A dark bonnet in a Joburg summer gets there easily.

So the practical lesson is the same either way: heat and time are the enemy. The same dropping does far more damage on a black bonnet in the afternoon sun than in the morning shade.

The grit is the other half of the problem. Wipe a dry dropping and you're dragging seeds and sand across the paint.

Sap is different

Tree sap is resin. It lands as a sticky drop and dries hard, close to varnish. It doesn't usually etch like a dropping, but it bonds, holds dirt and can leave a dull ghost if it sits long enough. Fresh sap is easy. Old sap needs dissolving, not scraping.

The Porsche crest on a grey bonnet reflecting the studio lights at EXD in Hyde Park.
A glossy bonnet reflecting the studio lights at EXD in Hyde Park.

The EXD Soften-and-Lift Method (droppings)

  1. Get it into the shade if you can, and let a hot panel cool.
  2. Soften it. Soak it with a quick detailer, or lay a warm, wet microfibre over it for a minute or two. Let it rehydrate.
  3. Lift, don't rub. Fold the towel and lift the softened mess off in one direction. Turn to a clean face for the next pass.
  4. Repeat rather than press. If some is left, soak again. Patience beats pressure.
  5. Rinse and look. Rinse the spot, dry it gently and check it in good light.

The EXD Sap Method

  1. Wash the area first so you aren't working grit into the paint.
  2. Use a dedicated tar and sap remover made for car paint. Spray it on, or hold a damp cloth with it on the spot, and let it dwell without drying.
  3. Wipe gently once it softens. Repeat on old sap rather than scrubbing.
  4. Rinse, then rewash the panel. Solvents can thin out wax or a topper on that spot, so give it a top-up if the car is protected.

Never

  • Never scrape with a fingernail, a card or a blade.
  • Never wipe a dry dropping with a dry cloth or a tissue.
  • Never use a kitchen scourer, household bleach or a wheel cleaner on paint.
  • Never use petrol, thinners or oily sprays on painted panels.

On PPF

Film helps here. The dropping sits on the film instead of your clear coat. Treat it the same way: soften, lift, rinse. Use only gentle, film-safe products. A quick detail spray made for paint and film is the safe first step.

XPEL's own care notes say to get bugs and bird residue off the film as soon as you can. Treat it the same way: soften, lift, rinse. On EXD film that carries FUSION PLUS, don't reach for XPEL Film Cleaner. XPEL South Africa is clear that it isn't for ceramic-infused film. Soften and lift with XPEL Detail Spray, or a pH-neutral quick detailer, and a soft microfibre. If a gentle lift doesn't clear it, stop and let us look at it. Don't clay film at home, and don't use alcohol or solvents on it.

On a ceramic coating

A coating buys you time. It does not make droppings harmless. Use a pH-neutral quick detailer, soak, lift, rinse. For sap on coated paint, a tar and organic-residue remover that is labelled safe on coatings is the right tool. Then a coating topper on that spot. GYEON's own maintenance guide says the same: if you can't remove it with the routine products, have a certified detailer look at it rather than trying harder.

When to bring it in

If the spot is clean but you can still see a dull ring or a crater in good light, that's etching. It's in the clear coat now, and no amount of washing will move it. Light etching often polishes out. Deep etching may only improve. That's a call I'd rather make under the studio lights with a paint gauge. WhatsApp a photo to +27 81 063 8786 and we'll take it from there.

What we use at EXD (optional note)

On coated paint, GYEON Q²M QuickDetailer for droppings and Q²M Tar for sap are what we reach for. On XPEL film that carries FUSION PLUS, XPEL Detail Spray, not XPEL Film Cleaner. You don't need these exact products. Any pH-neutral quick detailer made for car paint, used gently, follows the same method.

Try it

WhatsApp EXD on +27 81 063 8786. 386 Jan Smuts Avenue, Hyde Park, Johannesburg.