EXD_ Care Guides · Wash and care at home
How to wash your car at home without scratching the paint
Wash the wheels first with their own bucket, brush and mitt, then use two buckets and one mitt on the paint, with no rush. Rinse the mitt after every panel, work top down in straight light passes, and dry with a plush towel or a blower. This is the method I'd teach anyone, client or not.
Avi Nair, EXD · About 6 minutes · Published 8 June 2026
Most swirls I see in Hyde Park did not come from the N1. They came from a wash. A gritty mitt, a dry wipe across Joburg dust, a towel that last saw the wheels. Paint remembers all of it.
The good news is that a safe wash is not clever. It's a routine. Do the same steps in the same order and the paint stays clear for years.
Keep the grit away from the paint. Everything below serves that one rule.
What you need
- Two buckets, about 10 litres each. One for shampoo, one for clean rinse water.
- A grit guard in each bucket. It's a plastic grid that sits on the bottom. Dirt drops through it and stays down there, away from your mitt.
- A pH-neutral car shampoo. Not dish soap, not a household cleaner, not a wash-and-wax.
- Two soft microfibre wash mitts. One for the top half of the car, one for the bottom.
- A third bucket, a wheel brush and a wheel mitt that never touch the paint.
- One or two plush microfibre drying towels, or a blower.
- Optional: a pump sprayer or foam lance for a pre-wash.
Why not dish soap? It's made to strip grease off plates. On a car it strips wax and sealant, and it's harsh on a coating. Shampoo made for cars cleans and lubricates, so the mitt glides instead of drags.
Before you start
Wash in the shade, on cool panels. On a Highveld afternoon a black bonnet gets hot enough to dry shampoo before you can rinse it, and Joburg water leaves spots when it dries on warm paint. Early morning is easier on the car and on you.
New film? If XPEL film went on at EXD, don't wash it in the first week. Leave the first wash to us. Between day 4 and day 7 the car comes back to the studio for its final check and seal, with a complimentary wash, and we recheck the edges then.
New coating? Follow the curing note we gave you at handover before the first home wash.
The EXD Two-Bucket Method
- Wheels first. They carry brake dust and road grit, the worst stuff on the car. Use their own bucket, brush and mitt, and rinse them well. Never take the wheel mitt to the paint. Not even once. Not even the bumper.
- Rinse or foam. Wet the car from the top down to move loose dust before anything touches the paint. If you use a pre-wash foam, let it dwell for a few minutes, never let it dry, then rinse it off. The point is to lift grit without rubbing.
- Set up the buckets. Shampoo in one, clean water in the other, grit guards in both. Follow the dilution on the bottle. More shampoo is not more clean.
- Wash top down, one panel at a time. Roof, glass, bonnet, boot, upper doors. Use straight, light passes. Let the mitt and the suds do the work. No pressing, no circles. Circles drag grit around in rings, and rings are exactly what swirls look like.
- Rinse the mitt before you reload it. After every panel, dunk the mitt in the rinse bucket and rub it over the grit guard. Wring it out. Only then go back into the shampoo. This is the whole trick of the two-bucket method. The rinse bucket gets dirty so the shampoo bucket doesn't.
- Change mitts for the bottom. The sills, lower doors and rear bumper hold the most grit. Do them last, with your second mitt. If a mitt hits the ground, it's finished for the day. Wash it before you use it again.
- Rinse while it's wet. Rinse each section before the shampoo dries, top down.
- Dry gently. Lay a plush towel flat on the panel and pat or draw it towards you. No pressure, no scrubbing. A blower is even better around mirrors, badges and grilles. Open the doors and fuel flap and dry the shuts so drips don't run down a clean panel ten minutes later. Keep the wheel towel for the wheels.
A. Avi's tip
If a mitt hits the ground, it's finished for the day. Wash it before you use it again. The grit you just picked up is exactly what puts swirls in.
If the car has PPF
- Keep a pressure washer nozzle at least 1 metre from the film, use a wide 40-degree tip, spray square to the panel, and never aim at an edge, seam or wheel-arch lip. Edges are where water gets under film. If you aren't sure, use a hose instead.
- No wax on film, and no abrasive polish or rubbing compound. If the film has a light mark, warm water or a sunny afternoon often lets the top coat heal it.
- The only coating that goes on XPEL film at EXD is XPEL FUSION PLUS. GYEON and Labocosmetica go on paint, wheels, glass and interiors, never on the film.
- Skip wash-and-wax and "ceramic" shampoos on film. A plain pH-neutral shampoo with no wax is what XPEL South Africa asks for.
- Don't clay film at home, and don't use alcohol or solvents on it. If the film needs a deeper clean, bring it to the studio. We can do that as part of a professional decon.
If the car has a ceramic coating
Same method, same two buckets. Use a pH-neutral shampoo. Every month or so, a coating maintenance spray or topper from the same family as the coating keeps the water beading. On paint we use GYEON and Labocosmetica, so their own shampoos and toppers are the natural match. A coating makes washing easier. It does not make a dirty mitt safe.
A note on water
Two 10-litre buckets are the heart of this wash. Use a hose with a trigger nozzle, or a watering can for the rinse, and turn it off between rinses. If there are water restrictions in your area, follow them. The bucket method still works.
If someone else washes it
Skip automatic and brush car washes. The brushes have already washed other cars, and they drag that grit across yours.
A corner hand car wash is fine, if you ask for a few things. A clean mitt, not one that's been on the wheels or the car in front. No brushes on the paint. And no harsh degreaser on film.
Do's and don'ts
| Do | Don't |
|---|---|
| Shade and cool panels | Wash in hot sun |
| Wheels first, own tools | The same mitt on wheels and paint |
| Rinse first | Dry-wipe dust |
| Two buckets, grit guards | One bucket, one sponge |
| Straight lines | Circles and pressure |
| Pat dry | Let it air-dry |
| Hose on film | Jet at film edges |
| Corner hand wash, clean mitt | Automatic or brush wash |
When a wash isn't enough
If marks are still there on clean, dry paint, they're in the clear coat. More pressure on the driveway won't help. That's a job for paint correction, under proper lights. If you'd like a second opinion on yours, WhatsApp +27 81 063 8786 to arrange an inspection at the Hyde Park studio.
Try it
What we use at EXD
At the studio we wash with GYEON and Labocosmetica shampoos on paint and wheels, and use XPEL FUSION PLUS on XPEL film. You don't need these brands to follow this guide. Any good pH-neutral shampoo and soft microfibre will do the job. If you'd like our selection, ask about the EXD home-care kit.
WhatsApp EXD on +27 81 063 8786. 386 Jan Smuts Avenue, Hyde Park, Johannesburg.
.png)